Measurement-computing StrainBook/616 Manual de usuario Pagina 65
- Pagina / 146
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Bridge Configurations 6
Introduction …. 6-1
CN-115 Headers, Associated Jumpers, and Plug-In Options …… 6-2
Bridge Applications …… 6-3
Removing the Cover Plate …… 6-4
Excitation Connection …… 6-5
Installing a CN-115 ….. 6-6
Low Pass Filter Customization …… 6-7
Configuration Diagrams …… 6-8
Full-Bridge …… 6-8
Half-Bridge …… 6-9
Three-Wire Quarter-Bridge …… 6-10
High-Gain Amplifier …… 6-11
Connecting to the DB9 Channel Input Connector …… 6-12
CA-177 Strain Gage Cable …… 6-12
CA-189, DB9 Adapter Option …… 6-13
WBK16/LC Load Cell Shunt Cal Internal Option …… 6-15
CN-115-1 User-Configurable Plug-In Card Option
…… 6-20
Introduction
The strain gage is connected to the amplifiers through the Bridge Completion and Shunt Cal Network. This network
consists of user-supplied / user-installed resistors for bridge completion. Several
combinations of resistors and 3
different shunt values may be installed simultaneously. External connector tie points and the programmable
Input Configuration & Cal MUX determine the actual configuration in use.
Once the network is fully configured, most bridge configurations and resistances can be accommodated without re-
opening the box. The shunt resistors allow each bridge to be put into a known imbalance condition for setting or
verifying channel calibration. Shunt calibration allows a full-scale gain to be set without physically loading the bridge.
Page 6-12 discusses a DB9 Adapter option that provides a means of easily setting up a bridge configuration.
The following board layout shows locations of components referenced to in this chapter. The jumper positions are
default locations. Information regarding the CN-115 header and associated jumpers follows.
StrainBook Board Layout
StrainBook/616 User’s Manual 929494 Bridge Configurations 6-1
- StrainBook/616 1
- 489-0901 4
- 1086-0926 4
- 489-0902 4
- 1008-0901 4
- Table of Contents 7
- Chapter 7 – Triggers 8
- 967594 ix 9
- 967594 StrainBook/616 10
- Introduction 1 11
- What is StrainBook/616? 11
- 929494 StrainBook/616 12
- What Are WBKs? 13
- Operation Reference 2 15
- Basic Operation 16
- Channel Selection 17
- 967794 StrainBook/616 18
- A/D input source 19
- Triggers 21
- PDF NOTE: 22
- SYNC Notes: 23
- Programmable Features 24
- Operational Tips 24
- CH1 through CH8 27
- Status LEDS 27
- Associated Cables 30
- Software 4 31
- An Introduction to Software 32
- # Item Description 33
- 967594 Software 4-5 35
- 967594 Software 4-7 37
- Sensor Calibration 38
- 967594 Software 4-9 39
- Sensor Configuration Window 41
- Column Description 42
- Column Display Description 43
- (Units) 44
- 2 Point Manual Calibration 45
- 2 Point Auto Calibration 45
- Name Plate Calibration 48
- 967594 Software 4-19 49
- System Requirements 51
- Software Installation 52
- Install the Software 54
- How to make the connection: 57
- For DEDICATED Networks 62
- Bridge Configurations 6 65
- Introduction 65
- Bridge Applications 67
- Removing the Cover Plate 68
- Excitation Connection 69
- Installing a CN-115 70
- Configuration Diagrams 72
- B,D, or F Shunt 73
- CA-177 Strain-Gage Cable 76
- CN-189, DB9 Adapter Option 77
- Purpose of the WBK16/LC 79
- Caveats 82
- Installing a WBK16/LC 83
- Calibration Using WaveView 84
- Installing a CN-115-1 85
- Configuring a CN-115-1 86
- Digital (TTL) Trigger 89
- Triggers 7 89
- Multi-Channel Trigger 90
- Above-Level Trigger 91
- Below-Level Trigger 91
- Rising-Edge Trigger 92
- Falling-Edge Trigger 92
- Trigger Latency & Jitter 93
- Digital-Pattern Trigger 94
- Note: The Clock Divider 95
- 977694 StrainBook/616 96
- Connections for 16-Bit Mode 97
- Connections for 8-Bit Mode 98
- TTL Trigger 99
- External Clock 99
- 977794 StrainBook/616 100
- Overview 101
- CE Standards and Directives 101
- Safety Conditions 102
- Dust Cap 103
- Shielded 103
- BNC Connector 103
- Noise Considerations 104
- System Expansion 10 105
- Channel Expansion 106
- DIN 5 Power Pinout* 107
- CA-242 or 107
- CA-242-7 107
- 3.3 Amp limit 111
- @ 15 VDC * 111
- CA-74-1 (1 ft.) or 112
- CA-74-5 (5 ft.) 112
- CAUTION 113
- Product Care 115
- Driver Support 116
- Troubleshooting Tables 116
- Channel readings are wrong 118
- WaveView Scope stops 119
- Ethernet Problems 122
- WaveView Issues 124
- Frequently Asked Questions 125
- (4) Topic: Sampling Rates 126
- (5) Topic: Calibration 126
- Customer Support 127
- StrainBook/616 12 129
- Expansion Options 131
- Quick Guide 133
- 977194 Appendix A 134
- Before you run a test 139
- 977194 Appendix B 140
- Glossary 143
- 969597 Data Acquisition 144
Relacionado con productos y manuales para Hardware Measurement-computing StrainBook/616
(6 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales