Measurement-computing StrainBook/616 Manual de usuario Pagina 27
- Pagina / 146
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Connectors, Indicators, and Cables 3
Front Panel Connectors and Indicators …… 3-1
Rear Pannel Connectors, Indicators, and Power Switch …… 3-2
Associated Cables …… 3-4
Front Panel Connectors and Indicators
StrainBook/616 Front Panel
CH1 through CH8
Channel Input DB9 Female Connectors: These eight DB9 connectors are used for channel input.
Status LEDS
ACTIVE – Lights when a sample has been converted by the A/D converter.
READY – Lights when the unit is fully booted and is ready for software access.
POWER – Lights when power is turned on and is present.
Digital I/O, External Clock, TTL Trigger
Digital I/O, External Clock Input, and TTL Trigger Input connect to the StrainBook via a front panel
DB25F high-speed digital I/O connector.
For the16-bit mode, which is the default setup for WaveView, the following signals are present on the
DB25.
16 High-Speed Digital I/O Lines (D0 through D15)
TTL Trigger Input (TTLTRG) (pin 13)
+15 V, 50 mA max. (pin 23)
-15 V, 50 mA max. (pin 22)
two +5 V (pin 19 and pin 21), 250 mA max. (total)
External Clock Input (pin 20)
Digital Clock Output (pin 18) – for WBK17applications only
two Digital Grounds (pins 24 and 25)
To sample just 16 digital input signals, connect them directly to the digital I/O data lines as indicated
in the following pinout. D15 is the most significant bit, and D0 is the least.
StrainBook/616 User’s Manual 967794 Connectors, Indicators, and Cables 3-1
- StrainBook/616 1
- 489-0901 4
- 1086-0926 4
- 489-0902 4
- 1008-0901 4
- Table of Contents 7
- Chapter 7 – Triggers 8
- 967594 ix 9
- 967594 StrainBook/616 10
- Introduction 1 11
- What is StrainBook/616? 11
- 929494 StrainBook/616 12
- What Are WBKs? 13
- Operation Reference 2 15
- Basic Operation 16
- Channel Selection 17
- 967794 StrainBook/616 18
- A/D input source 19
- Triggers 21
- PDF NOTE: 22
- SYNC Notes: 23
- Programmable Features 24
- Operational Tips 24
- CH1 through CH8 27
- Status LEDS 27
- Associated Cables 30
- Software 4 31
- An Introduction to Software 32
- # Item Description 33
- 967594 Software 4-5 35
- 967594 Software 4-7 37
- Sensor Calibration 38
- 967594 Software 4-9 39
- Sensor Configuration Window 41
- Column Description 42
- Column Display Description 43
- (Units) 44
- 2 Point Manual Calibration 45
- 2 Point Auto Calibration 45
- Name Plate Calibration 48
- 967594 Software 4-19 49
- System Requirements 51
- Software Installation 52
- Install the Software 54
- How to make the connection: 57
- For DEDICATED Networks 62
- Bridge Configurations 6 65
- Introduction 65
- Bridge Applications 67
- Removing the Cover Plate 68
- Excitation Connection 69
- Installing a CN-115 70
- Configuration Diagrams 72
- B,D, or F Shunt 73
- CA-177 Strain-Gage Cable 76
- CN-189, DB9 Adapter Option 77
- Purpose of the WBK16/LC 79
- Caveats 82
- Installing a WBK16/LC 83
- Calibration Using WaveView 84
- Installing a CN-115-1 85
- Configuring a CN-115-1 86
- Digital (TTL) Trigger 89
- Triggers 7 89
- Multi-Channel Trigger 90
- Above-Level Trigger 91
- Below-Level Trigger 91
- Rising-Edge Trigger 92
- Falling-Edge Trigger 92
- Trigger Latency & Jitter 93
- Digital-Pattern Trigger 94
- Note: The Clock Divider 95
- 977694 StrainBook/616 96
- Connections for 16-Bit Mode 97
- Connections for 8-Bit Mode 98
- TTL Trigger 99
- External Clock 99
- 977794 StrainBook/616 100
- Overview 101
- CE Standards and Directives 101
- Safety Conditions 102
- Dust Cap 103
- Shielded 103
- BNC Connector 103
- Noise Considerations 104
- System Expansion 10 105
- Channel Expansion 106
- DIN 5 Power Pinout* 107
- CA-242 or 107
- CA-242-7 107
- 3.3 Amp limit 111
- @ 15 VDC * 111
- CA-74-1 (1 ft.) or 112
- CA-74-5 (5 ft.) 112
- CAUTION 113
- Product Care 115
- Driver Support 116
- Troubleshooting Tables 116
- Channel readings are wrong 118
- WaveView Scope stops 119
- Ethernet Problems 122
- WaveView Issues 124
- Frequently Asked Questions 125
- (4) Topic: Sampling Rates 126
- (5) Topic: Calibration 126
- Customer Support 127
- StrainBook/616 12 129
- Expansion Options 131
- Quick Guide 133
- 977194 Appendix A 134
- Before you run a test 139
- 977194 Appendix B 140
- Glossary 143
- 969597 Data Acquisition 144
Relacionado con productos y manuales para Hardware Measurement-computing StrainBook/616
(6 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales