Measurement-computing DaqBoard 3000USB Series Manual de usuario Pagina 95
- Pagina / 128
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Note: Specifications are subject to change without notice. 928691 Specifications - DaqBoard/3000USB Series 7-1
Specifications – DaqBoard/3000USB Series 7
I/O Comparison Matrix
Model
DaqBoard/
Analog Input
Channels (ADC)
Analog Output
Channels (DAC)
Digital I/O
Channels
Counter
Inputs
Timer
Outputs
3001USB 16SE / 8DE 4 24 4 2
3005USB 16SE / 8DE 0 24 4 2
3031USB 64SE / 32DE 4 24 4 2
3035USB 64SE / 32DE 0 24 4 2
General Specifications
Power Consumption (per board):
Model Power Consumption (Typical)*
*An optional power adapter (TR-2) will be required if the
USB port cannot supply adequate power. USB2 ports
are, by USB2 standards, required to supply 2500 mW
(nominal at 5V, 500 mA).
/3001USB 3000 mW
/3005USB 2000 mW
/3031USB 3400 mW
/3035USB 2400 mW
Power Output for DaqBoard/3000 USB
Output Power
Supply Voltage
Tolerance Pin Numbers
Power Allowed when
using USB Power
Power Allowed when
using External Power
+5 V ± 20% P5-19; J7-22; J8-25 2 mA 10 mA
+13 V ± 10% J8-1 1 mA 5 mA
- 13 V ± 10% J8-2 1 mA 5 mA
Environment:
Operating Temperature: -30 to +70°C; Storage Temperature: -40 to +80°C
Relative Humidity: 0 to 95% non-condensing
Communications Speed: USB 2.0 high-speed mode (480 Mbps) if available,
otherwise, USB1.1 full-speed mode (12 Mbps)
Acquisition Data Buffer: 1 MSample
Vibration: MIL STD 810E Category 1 and 10
Signal I/O Connectors: (
see chapter 2 for pinouts)
68-pin standard “SCSI type III” female connector (P5); Four 40-pin headers (J5, J6, J7, J8),
AMP# 2-103328-0
Option TB-100
: An optional TB-100 terminal board can be connected to the 3000USB board’s 68-
pin SCSI connector via a CA-G55, CA-56, or CA-56-6 cable. The TB-100 provides access to
16SE/8DE analog inputs, up to 4 analog outputs, 24 digital I/O, and all counter/timers. When
using TB-100 with 3035 or 3031 models the remaining 48SE/24DE are accessed through 40-pin
headers (
see chapter 2 for details).
Option TB-101
: An optional TB-101 screw terminal board can be mounted directly to a 3000USB
Series board, providing screw terminal connections for all of the board’s I/O (see chapter 2 for
details
).
Temperature Measurement Connector: (
see chapter 2 for pinouts)
4-channel TC screw-terminal block (TB7); Phoenix # MPT 0.5/9-2.54
External Power:
Connector: Switchcraft#RAPC-712
Power Range: 6 to 16 VDC (used when USB port supplies insufficient power,
or when an independent power supply is desired)
Over-Voltage: 20 V for 10 seconds, max.
- DaqBoard/3000USB Series 1
- 938390 5
- *324401C-01* 7
- Contents 9
- (1) Install Software 10
- 968492 IG-5 11
- 968492 IG-7 13
- How to Mount the TB-101 15
- Scenario 4: Using a DBK215 16
- 68-Pin SCSI Connecter 18
- XAPCR = A/D Pacer Clock I/O 20
- -- X-- = Not Connected 20
- 20
- 968492 IG-15 21
- (3) Start DaqView 22
- (4) Configure the System 23
- (5) Collect Data 24
- Customer Assistance 25
- Device Overviews 1 27
- Block Diagrams 28
- Connections 30
- Product Features 31
- 1-6 Device Overviews 32
- 1-8 Device Overviews 34
- 1-10 Device Overviews 36
- Solution: 37
- Example: 37
- 1-12 Device Overviews 38
- Calibration 39
- Analog Output 39
- 1-14 Device Overviews 40
- Counter Inputs 42
- Timer Outputs 42
- 1-18 Device Overviews 44
- Connections and Pinouts 2 45
- 68-Pin SCSI Connecter (P5) 46
- TB-101 Terminal Board Option 51
- TB-101 Pinouts 52
- Hardware Setups 56
- Scenario 2: Using a TB-100 57
- Scenario 3: Using a DBK215 58
- Safety Conditions 59
- 949290 User’s Manual 60
- Calibration 4 61
- Counter Input Modes 5 63
- Encoder Mode (see page 15) 68
- Counter/Totalize Mode 68
- Period Mode 70
- Pulsewidth Mode 73
- Timing Mode 75
- Encoder Mode 77
- Wiring for 1 Encoder 80
- Criteria 84
- Input Signal is Equal to X 84
- Driven by Condition 84
- Detecting Input Values 85
- See the TIP below 85
- The Setpoint Status Register 93
- DaqBoard/3000USB Series 7 95
- Analog Inputs 96
- AutoZero Disabled 97
- Type T thermocouple 98
- A/D Specifications 99
- Input Sequencer 99
- Triggering 100
- Digital I/O 101
- Pattern Generation Output 102
- Counters 102
- Frequency/Pulse Generators 103
- Software 103
- Accessories and Cables 104
- Dimensions 105
- Overview 107
- DBK215, pg. A-2 108
- 886994 Appendix A 108
- TB16 Supports BNCE thru BNCF 108
- Connection Tips 109
- System Examples 110
- WARNING ! 111
- DBK215, pg. A-6 112
- [2 Screws per-side] 112
- 886994 DBK215 A-7 113
- 886994 DBK215 A-9 115
- 886994 DBK215 A-11 117
- WARNING 118
- CAUTION 118
- 886994 DBK215 A-13 119
- Specifications for DBK215 120
- Signal Modes 121
- 938390 Appendix B 122
- Shielding 123
- TC Common Mode 123
- Analog Filtering 125
- Input and Source Impedance 125
- Crosstalk 125
- Glossary 127
- 887194 Glossary 128
Relacionado con productos y manuales para Hardware Measurement-computing DaqBoard 3000USB Series
(74 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales