Measurement-computing DBK Part 2 Manual de usuario

USER’S MANUAL DBK Options Part 2 of 2 Option Cards and Modules DBK41 through DBK609 DBK Option Cards

EMI Shield Plates for CE Compliance To reduce electro-magnetic interference (EMI) escaping from (or entering into) the enclosure, a CE kit provides

DBK48, pg. 20 967792 8B Isolated Signal Conditioning Module This page is intentionally blank.

DBK50 and DBK51 8-Channel Isolated Voltage Input Modules Overview …… 1 Input Attenuation/Gain Factors …… 2 Hardware Setup …… 2 Signal-to-Module Con

Input Attenuation/Gain Factors Gain and attenuation may be calculated using the formula: Input Range Function K 300 V Range Attenuates 60 100 V

Channel Filter Jumper Settings for DBK50 and DBK51 The low-pass filters have a default corner frequency of 3.5 Hz when the jumpers are in the LPF-s

To power the interface circuitry of the DBK50 [or DBK51] via the internal ±15 VDC power supply, JP1 must be set to “Analog Option Card Use.” However

DBK53 and DBK54 16-Channel Analog Input Multiplexing Modules DBK53 – Low Gain Programmable Module DBK54 – High Gain Programmable Module Overview ……

Hardware Setup Differential Mode The DBK53 and DBK54 are designed for floating-type differential measurements. Neither the high nor the low of the

Single-Ended Mode Ground referencing must also be observed with single-ended measurements. The following figure shows a typical single-ended hookup.

DaqBook/100 Series & /200 Series and DaqBoard [ISA type] Configuration Three setup steps and needed to configure DaqBooks/100 Series & /200

DBK Option Cards and Modules 989594 DBK53 and DBK54, pg. 5 DBK53 and DBK54 – Specifications Name/Function: DBK53 16-Channel Low-Gain Analog Mul

System Connection A short ribbon cable (CA-37-x) attaches the DBK41 to the main unit. Connecting the DBK41 to any port other than P1 may damage devi

DBK53 and DBK54, pg. 6 989594 DBK Option Cards and Modules

DBK55 8-Channel Frequency-To-Voltage Input Module Overview …… 2 Features of the DBK55 …… 2 Input S

Overview Features of the DBK55 The DBK55 can be used for diverse frequency-monitoring applications. Typical uses include measuring the flow of liquid

Input Signal Conditioning The DBK55 conditions the input signal in several ways to provide the best output accuracy. Reducing noise and limiting the

CAUTION The input signal may range from -15 to +15 V. Higher voltages may damage the DBK55. The digital input circuit is represented in the lef

The figure shows the effect of 10 ms debouncing on a noisy signal. To be counted, a rising edge must be preceded by a low sustained for at least 10 m

If the measured frequency is Fmin, then the scaled result is 0. If the measured frequency were Fmax, then the scaled result would be 4096 but is limi

DBK55 On-board Jumper Configurations Configuration Jumpers Channel Selected Functions JP3 and JP4 CH 0 JP23 and JP24 CH 1 JP43 and JP44 CH 2 J

DBK55, pg. 8 988793 DBK Option Cards and Modules Input Circuit Selection: Analog or Digital Each input channel can be set for th

Address Configuration via Rear Panel DIP Switch You can connect 1 or 2 DBK55 modules to a single main channel on the primary data acquisition device.

DBK41, pg. 6 877095 DBK Option Cards and Modules

Configuring the Primary Data Acquisition Device DaqBook/100 Series & /200 Series and DaqBoard [ISA type] Configuration Several setup steps of D

Connecting the DBK55 to Signals and to the Primary Data Acquisition Device You can connect the DBK55 module to your primary data acquisition device a

DBK55, pg. 12 988793 DBK Option Cards and Modules Specifications - DBK55 Name/Function: 8-Channel Frequency-to-Voltage Input Card

DBK60 3-Slot Expansion Chassis with Termination Panels Overview …… 1 Hardware Setup …… 2 1 – Turn off system power and disconnect DBK60 …… 3 2

The front panel has a male DB37 connector that leads to the acquisition processor via a CA-37-x, CA-37-xT, or equivalent cable. The rear panel is ma

1 – Turn off system power and disconnect the DBK60 If the DBK60 is presently connected in a system, turn off all system devices and disconnect the DBK

6 – Configure the chassis for the power source Use one power source, and only one power source, for cards on the P1 bus! +5 V is selected with the DB

7 – Install a power card, if needed If you determined [in step 5] that additional power is needed, add a DBK32A or DBK33 power card to the acquisition

DBK60, pg. 6 989594 DBK Option Cards and Modules 12 – Install the card drawer A. Hold the card drawer by its handle and tilt it up slightly. Plac

DBK65 8-Channel Transducer Interface Module The DBK65 is campatible with: WaveBook, ZonicBook, LogBook, DaqBook, DaqLab, DaqScan, and DaqBoard/20

DBK42 16-Slot 5B Signal Conditioning Module Overview …… 1 Hardware Setup …… 2 DBK42 Connection …… 2 DBK42 Configuration …… 2 5B Module Connectio

Each of the 8 channels can be set for a different excitation voltage. 5, 10, 15, and 24 VDC are provided internally from the DBK65 and are selected v

Selecting an Excitation Voltage Each channel has a voltage select header, which consists of 5 pairs of pins and a jumper. The jumper position determ

Customizing a Voltage To make use of the custom voltage feature you will need to acquire a resistor of the calculated value. The formula to use is:

Channel PGM Resistor Location Voltage Out Jumper Header Voltage Set VoutResistor Value R2CH00 R110 J11 CH01 R120 J21 CH02 R130 J31 CH

5. Using rosin core solder and proper soldering technique, solder the resistor into position for the applicable channel. Be sure that the resistor

Configuring the DBK65 Address You can connect 1 or 2 DBK65 modules to a single main channel on the primary data acquisition device. Thus, a 16-chann

Configuring the Primary Data Acquisition Device DaqBook/100 Series & /200 Series and DaqBoard [ISA type] Configuration Use of a DBK65 with a DaqBo

Connecting the DBK65 to Signals and to the Primary Data Acquisition Device You can connect the DBK65 module to your primary data acquisition device a

Tip: Label each transducer with its associated channel/sub-channel information. 2. For a single DBK65 module, connect one end of the P1 cable to

DBK Option Cards and Modules 988793 DBK65 pg. 11 Calibrating a Transducer using the “Shunt Calibration Technique” The “shunt calibration” techn

Each terminal block contains 4 terminals (per channel) for access to input and excitation features of 5B modules. The optional CN-71 and CN-72 sign

DBK65 pg. 12 988793 DBK Option Cards and Modules DBK65 Specifications Dimensions: 285 mm W x 220 mm D x 45 mm H (11” x 8.5” x 1.75”) Weight: 1

DBK65 I-V CURVE AT 5V EXCITATION0.0001.0002.0003.0004.0005.0006.0000.12350.12000.11860.11640.10900.08970.07610.06620.05850.05250.04790.04370.04020.0

DBK65 pg. 14 988793 DBK Option Cards and Modules

DBK70 Vehicle Network Interface The DBK70 has the following features: Measures up to 16 vehicle network parameters • • • • • Synchronously records

DBK70ref, pg. 2 989594 DBK Option Cards and Modules

DBK80 16-Channel Differential Voltage Input Card with Excitation Output Overview …… 1 Hardware Setup …… 2 Card Connection …… 2 Card Configuration ……

Hardware Setup Card Connection DBK80 Board Layout Referring to the figure above, voltage input signals are connected to the screw terminal blocks

Three examples of using the excitation source follow. They are Position Sensing, Resistance/Thermistor Measurement, and Reading a Transducer.

Source impedance below 1000 ohms will create negligible error. Above 1000 ohms, the effects are increasingly noticeable. An accurate source in serie

The excitation output voltage is set via JP2. JP2 Location Reference The above figure is of a partial DBK80. JP2 is shown selected to +5VDC. Note

DBK Option Cards and Module 967694 DBK42, pg. 3 A DBK42 populated with strain-gage modules will draw more current than with other types of input mo

DaqBook/2000 Series and DaqBoard/2000 Series Configuration No jumper configurations are required for the /2000 series devices. Software Setup The DBK

DBK81, DBK82, and DBK83 Thermocouple Cards DBK81 – 7 Channel Card DBK82 – 14 Channel Card DBK83 – 14 Channel Card with External Connecti

DBK81 Block Diagram* *The DBK81 block diagram can be applied to the DBK82 and DBK83, as their diagrams only differ to the one above in regard to the

It should be noted that thermocouples output very small voltages and that long thermocouple leads can pickup a large amount of noise. However, the DB

Using the Connection POD, DBK83 Only Unlike other DBK units, the input connections for the DBK83 do not exist on the card itself. Instead, they exist

To connect the POD-1 to the DBK83: 1. Connect the male end of the CA-239 cable to the female 44-pin connector on the DBK83. 2. Connect the female e

Card Configuration Up to sixteen DBK81, DBK82, or DBK83 cards can be attached to a single LogBook or Daq device, providing up to 224 temperature chann

Software Setup Reference Notes: o DaqView users - Refer to Chapter 3, DBK Setup in DaqView. o LogView users - Refer to Chapter 4, DBK Setup in L

pg. 8, DBK81, DBK82, & DBK83 989494 DBK Option Cards and Modules Using a Temperature Calibrator The DBK81, DBK82, and DBK83 thermocouple c

DBK Option Cards and Modules 989494 DBK81, DBK82, and DBK83 pg. 9 DBK81, DBK82, DBK83 - Specifications Name/Function: DBK81 – 7 Channel High-A

WARNING Shock Hazard! The DBK42 is designed to sense signals that may carry dangerous voltages. De-energize circuits connected to the DBK42 befo

TC Accuracy at Measurement Temperature in ˚C (±˚C) pg. 10, DBK81, DBK82, & DBK83 989494 DBK Option Cards and Modules

DBK84 14-Channel Thermocouple Module Overview …… 1 Hardware Setup …… 2 Module Connection …… 2 Open Thermocouple Detection …… 3 Module Configura

In comparison to typical DBK options, the DBK84 demands significant power from the system’s ±15 V power supplies. It is important that you calcul

through the use of shielded thermocouples and/or averaging. You can minimize the effect of noise by (1) using shielded thermocouples, (2) averagi

Module Configuration Up to sixteen DBK84 modules can be attached to a single LogBook or Daq device. Since multiple modules are connected via a paral

DaqBook/100 Series & /200 Series and DaqBoard [ISA type] Configuration Use of a DBK84 with a DaqBook/100 Series device, DaqBook/200 Series device

Software Setup Reference Notes: o DaqView users - Refer to Chapter 3, DBK Setup in DaqView. o LogView users - Refer to Chapter 4, DBK Setup in L

DBK Option Cards and Module 989494 DBK84 pg. 7 Using a Temperature Calibrator The DBK84 thermocouple module provides accurate and repeatable t

pg. 8, DBK84 989494 DBK Option Cards and Modules DBK84 - Specifications Name/Function: DBK84 – 14 Channel High-Accuracy Thermocouple Module S

DBK85 16-Channel Differential Voltage Module Overview …… 1

DaqBoard/2000 Series and cPCI DaqBoard/2000c Series Connections DBK42 can be connected to the P1 connector of DaqBoard/2000 Series P4-adapters. Up to

Overview The DBK85 is a low-noise, high-speed, unity-gain multiplexer module that provides 16 channels of differential voltage input. Up to 16 DBK85

Configuring the Primary Data Acquisition Device DaqBook/100 Series & /200 Series and DaqBoard [ISA type] Configuration Use of a DBK85 with a Daq

CE Compliance If your data acquisition system needs to comply with CE standards, the DBK85 must be connected to the LogBook or Daq device by a CA-143

Analog Common DBK85’s analog common connector is located just left of the channel 1 BNC. The connector is typically used to provide a ground referenc

Specifications – DBK85 Connectors: DBK37 male connector designated as P1. Connects to P1 on a DaqBook, DaqBoard, or LogBook via a CA-37-x or a CA-1

DBK Option Cards and Module 907492 DBK90 pg. 1 DBK90 56-Channel Thermocouple Module For use with DaqBook/2000 Series Devices, WBK40, &

pg. 2, DBK90 907492 DBK Option Cards and Modules Overview The DBK90 is used in temperature measurement applications and provides connections f

DBK Option Cards and Module 907492 DBK90 pg. 3 Hardware Setup Connecting DBK90 Modules to Thermocouples The DBK90 accepts up to 56 mini-TC plu

pg. 4, DBK90 907492 DBK Option Cards and Modules Open Thermocouple Detection The DBK90 is equipped with open thermocouple detection for each ch

DBK Option Cards and Module 907492 DBK90 pg. 5 Connecting DBK90 Modules to other Devices Mounting DBK90 Modules to Each Other – Using Kit # 110

Software Setup You will need to set several parameters so DaqView can best meet your application requirements. After the 5B module type is identi

pg. 6, DBK90 907492 DBK Option Cards and Modules Mounting one or two DBK90 Modules to a Primary Data Acquisition Device – Using Kit # 1109-

DBK Option Cards and Module 907492 DBK90 pg. 7 Mounting one, two, or three DBK90 Modules to a DBK60 – Using Kit # 1109-0803 Mounting kit p/n

pg. 8, DBK90 907492 DBK Option Cards and Modules Mounting a DBK90 to a Rack – Using Rack-Mount Kit # 1109-0801 You can use Rack-Mount Kit # 110

DBK Option Cards and Module 907492 DBK90 pg. 9 Vehicle Testing and Noise Reduction Power Connections and Analog Common To properly measure vehi

pg. 10, DBK90 907492 DBK Option Cards and Modules Shielding Using shielded TC wire with the shield connected to analog common [DBK90’s ACOM jack

DBK Option Cards and Module 907492 DBK90 pg. 11 Software Setup Reference Notes: o DaqView users - Refer to DBK Setup in the DaqView PDF. o

pg. 12, DBK90 907492 DBK Option Cards and Modules Using a Temperature Calibrator The DBK90 thermocouple module provides accurate and repeatable

DBK Option Cards and Module 907492 DBK90 pg. 13 DBK90 – Specifications Note: Specifications are subject to change without notice. System Comp

pg. 14, DBK90 907492 DBK Option Cards and Modules Ordering Information Note: Ordering information is subject to change without notice. Descr

DBK100 Series In-Vehicle Thermocouple Measurement System DBK100/D, DBK100/T, and DBK101 Overview …… 2 System Compatibility: DaqBook/2000* Ser

DBK Option Cards and Module 967694 DBK42, pg. 7 Engineering Units Conversion Using mx + b Most of our data acquisition products allow the user to c

Overview Features o Measure vehicle engine temperatures with remote DBK100s o One cable transmits up to 56 channels of TC measurements from the en

DBK Option Cards and Module 907994 DBK100 Series pg. 3 The benefit of a DBK100 system is that for every 56 TC input channels, only a single cab

DBK100 Connectors: 2 control connectors allow for daisy chaining between units and connection to the DBK101 hub. Each control connector has 9 signal

Hardware Setup Connecting Thermocouples Each DBK100/D and DBK100/T can accept up to 14 mini-TC plugs in its channels 0 through 13. All channels have

DBK100/D is terminated in a Deutsch connector, enabling watertight connections to a mating connector with up to 14 thermocouples. Custom pin-configura

Open Thermocouple Detection DBK101 is equipped with open thermocouple detection. This means that a broken thermocouple wire [or otherwise unconnected

pg. 8, DBK100 Series 907994 DBK Option Cards and Modules Both DBK101 hubs have 8 strings of DBK100 modules (1 string per DBK101channel). In th

Vehicle Testing and Noise Reduction Power Connections and Analog Common To properly measure vehicle-attached thermocouples differentially, it is nece

The lines that will connect to the vehicle battery are soldered to the male DIN5 connector. As indicated in the first figure on this page, the +VIN

A thin layer of heat-sink compound on the indicated surfaces will improve thermal conductivity. The length of the shoulder washer’s hub must not exc

ii

DBK42, pg. 8 967694 DBK Option Cards and Modules DBK42 – Specifications Name/Function: 16-Slot 5B Signal Conditioning Module Module Capacity: 16

With One DBK101 and Full Bank Mode Disabled Base Channels 0, 1, 2, and 3 are occupied Reference Note: In relation to the above figure, you may wa

In the following figure we see that J-type thermocouples have been selected for Channels 0 through 23; possibly more, but we would have to scroll down

pg. 14, DBK100 Series 907994 DBK Option Cards and Modules Using a Temperature Calibrator DBK100 Series / DBK101 systems provide accurate and re

DBK Option Cards and Module 907994 DBK100 Series pg. 15 Specifications – DBK100 Series Note: Specifications are subject to change without not

pg. 16, DBK100 Series 907994 DBK Option Cards and Modules Power Requirements DBK100/D: 10 mA from +15V, 10 mA from -15V, 300 mW total DBK100/T:

DBK200 Series Matrix The DBK200 Series Matrix is presented on the following page. It is preceded

DBK200 Series, Adapter Board Matrix, pg. 2 967194 DBK Option Cards and Modules The following matrix provides a quick comparison of the DBK2

DBK202, DBK203, DBK204 Series P4-to-P1 / P2 / P3 Adapters For Analog I/O, Digital I/O, & Pulse/Frequency Fo

pg. 2, DBK202, DBK203, and DBK204 Series 938994 DBK Option Cards and Modules Overview The various part numbers [DBK202, /203, /203A, /204

Screw-Terminal Adapter Board The DBK202 Board provides a means of connecting channel input signals to a /2000 Series device through one of three meth

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 1 DBK43A and DBK43B 8-Channel Strain Gage Modules Overview …… 1 Hardware Connection …

pg. 4, DBK202, DBK203, and DBK204 Series 938994 DBK Option Cards and Modules Connection Tips CAUTION Turn off power to the host PC and

5. The board’s 100-pin P4 connector connects to the DaqBoard/2000 P4 connector via a CA-195 Cable. 6. To obtain maximum protection from static, con

pg. 6, DBK202, DBK203, and DBK204 Series 938994 DBK Option Cards and Modules Using Screw-Terminal Blocks CAUTION Turn off power to the

The following pages correlate the DBK202 terminal block connectors with the associated pins of the P1, P2, and P3 DB37 connectors. Note that the S

pg. 8, DBK202, DBK203, and DBK204 Series 938994 DBK Option Cards and Modules Correlation to P1 – Pertains to Terminal Blocks TB9, TB10,

Correlation to P2 – Pertains to Terminal Blocks TB5, TB6, TB7, and TB8 for Digital I/O. TB5 P2 Pin Number and Description DGND * Digital Ground,

pg. 10, DBK202, DBK203, and DBK204 Series 938994 DBK Option Cards and Modules Correlation to P3 – Pertains to Terminal Blocks TB1, TB2, TB

Using the P3 Header CAUTION Disconnect the DBK202, DBK203, DBK203A, DBK204, or DBK204c from power and from signal sources prior to connecting the CA

pg. 12, DBK202, DBK203, and DBK204 Series 938994 DBK Option Cards and Modules Adding Resistor/Capacitor Filter Networks WARNING Disconnec

An Example of Customer-Installed Capacitors and Filters for RC Networks on a DBK202 Prior to installing RC components, review the previous WARNING a

DBK43A & DBK43B, pg. 2 899892 DBK Option Cards and Modules For half-bridge and quarter-bridge strain gages, the modules can accommodate user-s

pg. 14, DBK202, DBK203, and DBK204 Series 938994 DBK Option Cards and Modules

DBK205 P4 to 12-Slot Screw Terminal Adapter For DaqBoard/2003 and cPCI DaqBoard/2003c Not Applicable to DaqBook/2000 Series Devices Overview ….. 1 Co

DBK205, pg. 2 987594 DBK Option Cards and Modules Although a 3-foot, 100-conductor ribbon cable (part number CA-195) is typically used to co

DBK206 P4-to-P1/P2/P3 Adapter Board For Analog I/O, Digital I/O, & Pulse/Frequency Overview …… 1 Connections …… 1 Note: DBK206 provides: P1, P2,

DBK206, pg. 2 987594 DBK Option Cards and Modules Regardless of which method is used, the DBK206 connects to the 100-pin P4 connector of a D

DBK Option Cards and Modules 987594 DBK206, pg. 3 5. To obtain maximum protection from static, connect the CHASSIS terminal to earth ground. 6. F

DBK206, pg. 4 987594 DBK Option Cards and Modules Correlation to P1 – TB11, TB10, TB9, and TB12 for Analog I/O. TB11 P1 Pin Number and D

Correlation to P2 – TB5, TB6, TB7, and TB8 for Digital I/O. TB7 P2 Pin Number and Description C0 29 Digital I/O: P2, Digital Port C, Bit 0; or P2 E

DBK206, pg. 6 987594 DBK Option Cards and Modules Correlation to P3 – TB1, TB2, TB3, and TB4 for Pulse/Frequency/Digital I/O. TB1 P3 Pin Nu

DBK207 and DBK207/CJC 5B Carrier Boards For 5B-Compatible Analog Input Modules Overview …… 1 Warnings, Cautions, and T

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 3 Hardware Connection Power Connection The strain gage modules each require an input v

DBK207 and DBK207/CJC, pg. 2 987594 DBK Option Cards and Modules WARNING Ensure that hard-wire emergency over-ride circuitry exists for al

Warnings, Cautions, and Tips WARNING Ensure that hard-wire emergency over-ride circuitry exists for all applications that make use of dangerous switc

DBK207 and DBK207/CJC, pg. 4 987594 DBK Option Cards and Modules Power The DBK207 and DBK207/CJC require +5 VDC from a regulated DC power su

Channel Configuration Up to 16 DBK207 [DBK207/CJC] boards can be connected to a Daq-based acquisition system. Since this is a daisy-chain interface,

DBK207 and DBK207/CJC, pg. 6 987594 DBK Option Cards and Modules Terminal Block Connection WARNING Shock Hazard. De-energize circuits c

Connecting DBK207 or DBK207/CJC to a Daq Device DBK207 and DBK207/CJC can be connected to the P4 connector of a DaqBook/2000 Series device or a DaqBo

DBK207 and DBK207/CJC, pg. 8 987594 DBK Option Cards and Modules DBK207 and DBK207/CJC – Specifications Name/Function: DBK207 – Carrier

DBK208 Relay Carrier Board For Opto-22 Compatible Solid-State-Relays Overview …… 1 Warnings, Cautions, and Tips …… 3 Power …… 4 External Power Watchd

DBK208, pg. 2 987594 DBK Option Cards and Modules WARNING Ensure that hard-wire emergency over-ride circuitry exists for all applications

Note that a single Daq-based data acquisition system can support up to 16 DBK208 boards, providing a total of 256 channels. DBK208 boards contain two

DBK43A & DBK43B, pg. 4 899892 DBK Option Cards and Modules DBK43A uses a mini-DIN6 connector with pre-defined wire color coding based on a CA-1

DBK208, pg. 4 987594 DBK Option Cards and Modules 1. Provide raceways (protective wiring routes) for all external I/O wiring. 2. Keep ex

External Power Watchdog The External Power Watchdog is governed by the setting of the JP2 jumper. This jumper allows the user to determine the behav

DBK208, pg. 6 987594 DBK Option Cards and Modules DBK208 Board # Switch S1 Configurations Address Designation in DaqView (see notes 2 &am

Software Setup Note: DBK208 is not applicable to LogBook or LogView. To use DBK208 from within DaqView, you must first configure the DaqView softwa

DBK208, pg. 8 987594 DBK Option Cards and Modules Configure System Hardware and DBK208 Configuration Settings Windows Switch Settings The

DBK Option Cards and Modules 987594 DBK208, pg. 9 DBK208 – Specifications Name/Function: Carrier Board for Opto-22 Compatible Solid-State-Relays M

DBK208, pg. 10 987594 DBK Option Cards and Modules

DBK209 P4-to-P1/P2/P3 Mini-Adapter Board For Analog I/O, Digital I/O, & Pulse/Frequency Overview …… 1 Connections …… 2 DBK209 Dimensional Drawing

DBK209, pg. 2 909094 DBK Option Cards and Modules Connections CAUTION Turn off power to the host PC and externally connected equipment pr

Connection tips: • Ensure power is removed from the device(s) to be connected. • Observe ESD precautions when handling boards and making connections

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 5 DBK43B (Rear Panel)** ** With exception of the rear panel area, the DBK43B has

DBK209, pg. 4 909094 DBK Option Cards and Modules

DBK210 32 Channel Digital I/O Carrier Board for GrayhillTM 70M-Series Mini-Modules Overview …… 1 Warnings, Cautions, and Tips …… 4 Power …… 5 Externa

DBK210, pg. 2 987594 DBK Option Cards and Modules DBK210 is a four-bank carrier board for optically-isolated Grayhill 70M-Series mini-module

DBK210 boards are typically installed in NEMA-type panels; however, they can be installed on DIN rails. Separate mounting instructions are included w

DBK210, pg. 4 987594 DBK Option Cards and Modules Warnings, Cautions, and Tips WARNING Ensure that hard-wire emergency over-ride circuitry

Power The DBK210 requires an external isolated 5 volt DC power supply with at least 0.600 amp current capacity. External power attaches to the DBK210

DBK210, pg. 6 987594 DBK Option Cards and Modules Setting the Local Address Set via S1, Swi

Software Setup Note: DBK210 is not applicable to LogBook or LogView. To use DBK210 from within DaqView, you must first configure the DaqView softwar

DBK210, pg. 8 987594 DBK Option Cards and Modules 5. Set S1 micro-switches to agree with the actual settings of the switches on the DBK210

DaqView’s Channel Setup Tab In the above figure the 4 Banks for one DBK210 card are listed in the CH column as: P2 0-A, P2 0-B, P2 0-C, and P2 0-D.D

DBK43A & DBK43B, pg. 6 899892 DBK Option Cards and Modules Bridge Applications There are several ways to hook-up strain gages—all are configure

DBK210, pg. 10 987594 DBK Option Cards and Modules DBK210 – Specifications Name/Function: Carrier Board for GrayhillTM 70M-Series Mini-Modu

DBK213 Screw-Terminal & Expansion Card Module 3-Card Slot, Includes P1/P2/P3/P4 compatibility for Analog I/O, Digital I/O, &

DBK213, pg. 2 969294 DBK Option Cards and Modules Connection Tips CAUTION Turn off power to the host PC and externally connected equipment

Installing DBK Cards Front Panel with 3 Vacant Card Slots P1 P2 P3 Rear Pa

DBK213, pg. 4 969294 DBK Option Cards and Modules System Examples Example 1: DaqBoard/2000 • DBK7 Analog I/O Card • DBK25 Digital I/

Example 2: DaqBoook/2001 • DBK7 • DBK80 • DBK82 -------- (3 Analog

DBK213, pg. 6 969294 DBK Option Cards and Modules Using the Screw-Terminal Blocks You must remove the DBK213 module’s cover plate to access

Correlation to P1 – Pertains to Terminal Blocks TB9, TB10, TB11, and TB12 for Analog I/O. TB9 P1 Pin Number and Description (see Note 1) DIFF SE

DBK213, pg. 8 969294 DBK Option Cards and Modules Correlation to P2 – Pertains to Terminal Blocks TB5, TB6, TB7, and TB8 for Digital I/O.

Correlation to P3 – Pertains to Terminal Blocks TB1, TB2, TB3, and TB4 for Pulse/Frequency/Digital I/O. TB1 P3 Pin Number and Description D0 10 P3

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 7 The Kelvin connection using the remote sensing lines performs best when the entire

DBK213, pg. 10 969294 DBK Option Cards and Modules Adding Resistor/Capacitor Filter Networks WARNING Disconnect the DBK213 from power and s

• Do not use RC filters in conjunction with additional DBK expansion accessories. • Prior to installing a resistor to the filter network you

DBK213, pg. 12 969294 DBK Option Cards and Modules Specifications for DBK213 Operating Environment: Temperature: -30°C to 70°C Relative Hu

Reference Notes: In regard to calculating system power requirements refer to the DBK Basics section. Chapter 2 includes pinouts for P1, P2, P

DBK213, pg. 14 969294 DBK Option Cards and Modules

DBK214 16-Connector BNC Interface Module Includes P1/P2/P3/P4 compatibility for Analog I/O, Digital I/O, &

DBK214, pg. 2 967894 DBK Option Cards and Modules DBK214 Block Diagram * Accessory Kit p/n 1139-0800 includes jumper wires and a screw d

Connection Tips CAUTION Turn off power to the host PC and externally connected equipment prior to connecting cables or signal lines to DBKs. Electr

DBK214, pg. 4 967894 DBK Option Cards and Modules System Examples Example 1: DBK214 Connected to a DaqBoard/2000 Note regarding the ab

Example 2: DBK214 Connected to a DaqBook/2001 Notes regarding the above s

DBK43A & DBK43B, pg. 8 899892 DBK Option Cards and Modules Bridge Configuration Settings for DBK43A and DBK43B

DBK214, pg. 6 967894 DBK Option Cards and Modules Using the Screw-Terminal Blocks You must remove the DBK214 module’s cover plate to access

In general, the following terminal block-to-signal relationships apply: DBK214 Terminal Blocks Used for . . . Alternative TB9 TB10 ANALOG INPUT P1,

DBK214, pg. 8 967894 DBK Option Cards and Modules Correlation to P1 – Pertains to Terminal Blocks TB9, TB10, TB11, and TB12 for Analog I/O.

Correlation to P2 – Pertains to Terminal Blocks TB5, TB6, TB7, and TB8 for Digital I/O. TB5 P2 Pin Number and Description DGND * Digital Ground,

DBK214, pg. 10 967894 DBK Option Cards and Modules Correlation to P3 – Pertains to Terminal Blocks TB1, TB2, TB3, and TB4 for Pulse/Frequenc

P1 Correlation to Analog Input BNC Terminations – BNC Ch 0 through BNC Ch 7 “Virtual” Terminal Blocks TB13 and TB14 for ANALOG INPUT connect to TB9 an

DBK214, pg. 12 967894 DBK Option Cards and Modules Adding Resistor/Capacitor Filter Networks WARNING Disconnect the DBK214 from power and s

• Do not use RC filters in conjunction with additional DBK expansion accessories. • Prior to installing a resistor to the filter network you

DBK214, pg. 14 967894 DBK Option Cards and Modules Specifications for DBK214 Operating Environment: Temperature: -30°C to 70°C Relative Hu

Reference Notes: In regard to calculating system power requirements refer to the DBK Basics section. Chapter 2 of the DBK Options Manual incl

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 9 Input Configuration Headers Eight 2×6 pin-headers with pin numbers 1 to 12 are on t

DBK214, pg. 16 967894 DBK Option Cards and Modules

DBK215 16-Connector BNC Connection Module With 68-Pin SCSI Adaptability for Analog I/O, Digital I/O, & Pulse/Fr

DBK215, pg. 2 897994 DBK Option Cards and Modules DBK215 Block Diagram * Accessory Kit p/n 1139-0800 includes jumper wires and a screw d

Connection Tips CAUTION Turn off power to the host PC and externally connected equipment prior to connecting cables or signal lines to DBKs. Electr

DBK215, pg. 4 897994 DBK Option Cards and Modules System Example DBK215 Connection to a DaqBoard/500 Series or DaqBoard/1000 Series Boar

Using the Screw-Terminal Blocks You must remove the DBK215 module’s cover plate to access the screw terminal blocks. This i

DBK215, pg. 6 897994 DBK Option Cards and Modules In general, the following terminal block-to-signal relationships apply: DBK215 Terminal B

Analog I/O Correlation to 68-pin SCSI Also see “Correlation to BNC Terminations (TB13 and TB14) on page DBK215-10.” TB9 Pin Number and Description DI

DBK215, pg. 8 897994 DBK Option Cards and Modules Digital I/O Correlation to 68-pin SCSI TB5 Pin Number and Description DGND ** Digital

Pulse/Frequency Correlation to 68-pin SCSI TB1 Pin Number and Description D0 N/A P3 Digital Port Bit 0 D1 N/A P3 Digital Port Bit 1 D2 N/A P3 Digital

DBK Cards & Modules Part 2 of 2

DBK43A & DBK43B, pg. 10 899892 DBK Option Cards and Modules A formula used to calculate the shunt-cal resistance value is: RShunt = [RGage

DBK215, pg. 10 897994 DBK Option Cards and Modules Correlation to Analog Input BNC Terminations – BNC 0 through BNC 7 “Virtual” Terminal Blo

Adding Resistor/Capacitor Filter Networks WARNING Disconnect the DBK215 from power and signal sources prior to installing capacitors or resistors.

DBK215, pg. 12 897994 DBK Option Cards and Modules • Do not use RC filters in conjunction with additional DBK expansion accessories.

DBK Option Cards and Modules 897994 DBK215 pg. 13 Specifications for DBK215 Operating Environment: Temperature: -30°C to 70°C Relative Humidity:

DBK215, pg. 14 897994 DBK Option Cards and Modules

DBK601 through DBK609 Termination Panels For use with DaqBook/260, DBK60, and LogBook/360 Reference Notes: DaqBook/260 users – refer to the DaqBo

WARNING Electrical Shock Hazard! To avoid possible injury and equipment damage, turn off power to devices and connected equipment prior to setup.

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 11 AC Coupling and Low-Pass Filter Options Per channel, the strain gage modules each a

DBK43A & DBK43B, pg. 12 899892 DBK Option Cards and Modules P1 Output Channel and Card Address Selection All 8 channels on the strain gage mod

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 13 2. For DaqBook/100, DaqBook/112 and DaqBook/120, place the JP4 jumper in single-

DBK43A & DBK43B, pg. 14 899892 DBK Option Cards and Modules Software-Controlled Setup Proper setup includes the use of software to control the

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 15 DBK43B Channel Types and Modes - Switch Positions Channel Type 1 (Mode) 1

DBK43A & DBK43B, pg. 16 899892 DBK Option Cards and Modules A Typical Setup Procedure, with Embedded Examples Reference Notes: Prior to usin

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 17 Load Cell Example Load cells come with a mV/V specification; for each volt of excit

DBK43A & DBK43B, pg. 18 899892 DBK Option Cards and Modules After we decide on a distribution option, the sensor can be hooked up to the DBK43

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 19 Typical input gain settings are shown in the following table. Input Gains and Typi

DBK Cards & Modules

DBK43A & DBK43B, pg. 20 899892 DBK Option Cards and Modules 15. Calculate the LogBook or Daq device voltage/transducer units. Do this using t

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 21 GageCal, Calibration Program for DBK16, DBK43A, and DBK43B in Daq Applications Gage

DBK43A & DBK43B, pg. 22 899892 DBK Option Cards and Modules Selecting DBK43A 4. Click the <OK> button. The Strain Gage Calibration wi

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 23 6. Select the type of calibration to be performed, i.e., Nameplate, Two-Point, or

DBK43A & DBK43B, pg. 24 899892 DBK Option Cards and Modules

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 25 Calibrating DBK16, DBK43A, or DBK43B for LogBook Applications Overview …… 25 Cali

DBK43A & DBK43B, pg. 26 899892 DBK Option Cards and Modules There are four trimpots to set up each channel circuit. The trimpots are labeled t

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 27 Shunt – Used to setup the channel using a shunt resistor applied to the bridge to s

DBK43A & DBK43B, pg. 28 899892 DBK Option Cards and Modules For all of the strain gage channels that are to be adjusted, set their ranges to +5

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 29 Selecting “Mode = Excitation” for DBK Parameter 1 Note: The Param2 column will sho

967194 DBK Cards & Modules DBKs Covered in Part 2 of 2 (with exception of DBK70)DBK41, 10-Slot Expansion Module DBK42, 16-Slot 5B Signal Con

DBK43A & DBK43B, pg. 30 899892 DBK Option Cards and Modules 11. DBK43A users: In LogView, open the LogBook Hardware Configuration Window (hard

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 31 VLC = (10 * 2.05×10-3) = 20.5 mV If 1000 pounds were applied, we would see 6.

DBK43A & DBK43B, pg. 32 899892 DBK Option Cards and Modules Note: Maximum gain calibration is x1000 for +5V range. The majority of the gain s

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 33 Channel Calibration Procedure Adjust the Offset The following steps are used to adj

DBK43A & DBK43B, pg. 34 899892 DBK Option Cards and Modules “Mode = SetInputGain,” 5 milli-Volt Reference Route 3. Turn off all the channel

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 35 3. Turn off all the channels in the system except for those DBK43A channels that

DBK43A & DBK43B, pg. 36 899892 DBK Option Cards and Modules “Mode = Bridge,” Reference Route 3. Turn off all the channels in the system exc

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 37 4. Select Mode = Bridge from the drop down list above the grid. This selection co

DBK43A & DBK43B, pg. 38 899892 DBK Option Cards and Modules Shunt Calibration Shunt calibration is virtually identical to the 2-Point method ju

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 39 For DBK16, only … Externally apply the shunt resistor and set the voltage to VD, a

iv 917594 DBK Option Cards & Modules User’s Manual Discontinued DBKs The following DBKs have been discontinued. However, documentation for them

DBK43A & DBK43B, pg. 40 899892 DBK Option Cards and Modules 9. Select Indicators \ Enable Input Reading Column from the menu bar to display th

DBK Option Cards and Module 899892 DBK43A & DBK43B, pg. 41 Periodic Calibration Without Trimpots Once the trimpots have been adjusted during

DBK43A & DBK43B, pg. 42 899892 DBK Option Cards and Modules Specifications - DBK43A and DBK43B Strain Gage Modules The following specification

DBK44 2-Channel 5B Signal-Conditioning Card Overview ….. 1 Hardware Setup ….. 2 Power Considerations ….. 2 Card Configuration ….. 3 5B Module C

The LogBook or Daq device scans the DBK44’s channels at the same 10 µs/channel rate as other DBKs (256 scans in 2.56 ms in a full system). Each use

Card Configuration Up to 128 DBK44s may connect to a LogBook or a Daq device system. Since this is a daisy-chain interface, each module must appear u

When installing current input modules (SC-5B32 series), be sure to install the current-sense resistor (SC-AC-1362 shipped with the SC-5B32) in the r

Note: A series of interface cables are available to connect up to 128 DBK44s. You can also use a DBK41 10-slot expansion chassis. DBK44 can be conn

DaqBook/2000 Series and DaqBoard/2000 Series Configuration No jumper configurations are required for these 2000 series devices. Software Setup Refere

DBK Option Cards and Modules 877095 DBK44, pg. 7 mx+b Values for 5B Modules The mx+b calculations for most 5B modules are included within LogView s

DBK41 10-Slot Expansion Module Overview …… 1 Hardware Setup …… 2 Card Configuration …… 2 Power Configuration …… 2 Card Insertion …… 3 EMI Shield

DBK44, pg. 8 877095 DBK Option Cards and Modules DBK44 – Specifications Name/Function: 2-Channel 5B Signal Conditioning Card Module Capacity: 2 “i

DBK45 4-Channel SSH and Low-Pass Filter Card Overview …… 1 Hardware Setup …… 2 Card Connection …… 2 Card Configuration …… 2 Configuring DBK45 Fil

DBK45 Block Diagram Hardware Setup Card Connection CAUTION Input voltage levels must not exceed ±5 V bipolar or 10 V unipolar. DBK45 is equipped

Address Configuration Up to four DBK45s can be connected to each analog channel. With 16 main channels and 4 inputs per DBK45, 256 inputs are possib

The right-hand figure shows the DIP-16 component pattern typical of the 4 filter sections. Note: “n” corresponds to “channel number.” Pin 7 of the

DaqBook/100 Series & /200 Series and DaqBoard [ISA type] Configuration Use of the DBK45 requires setting jumpers in DaqBooks/100 Series & /2

DBK45, pg. 6 987696 DBK Option Cards and Modules DBK45 – Specifications Name/Function: Simultaneous Sample and Hold and Low-Pass Filter Card Num

DBK46 4-Channel Analog Output Card Overview ... 1 For use with: DaqBook/2000ADaqBook/2000EDaqBook/2000XWBK41Hardware Setup ... 3 Software Setup

DBK46, pg. 2 967194 DBK Option Cards and Modules WBK41 Front Panel, Right-Edge Terminal Block Internal DAC Pacer ClockInternal Acquisition Pacer

Hardware Setup DBK46 is installed at the factory. To verify that a DBK46 is installed, simply check the acquisition software’s Analog Output Window

Hardware Setup Setup concerns include card and power configuration, proper card insertion, the use of EMI shields for CE compliance, and mounting [or

DBK46, pg. 4 967194 DBK Option Cards and Modules DBK46 – Specifications The four analog output channels are updated synchronously relative to sc

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 1 DBK48 Multipurpose Isolated Signal-Conditioning Modu

DBK48, pg. 2 967792 8B Isolated Signal Conditioning Module Safety Concerns WARNING Shock Hazard! Voltages above 50 Vrms AC and voltages above 100

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 3 Hardware Setup DBK48 Circuit Board Layout

DBK48, pg. 4 967792 8B Isolated Signal Conditioning Module Installing 8B Modules WARNING Electric shock hazard! Turn off power to the DBK48 and

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 5 Installing Plug-in Resistors to Create 4 to 20 mA Lo

DBK48, pg. 6 967792 8B Isolated Signal Conditioning Module Making Terminal Block Connections Input signals (and excitation when applicable) are wir

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 7 Setting DBK48 Module Addresses Up to sixteen DBK48 m

DBK48, pg. 8 967792 8B Isolated Signal Conditioning Module Configuring the Primary Data Acquisition Device DaqBook/100 Series & /200 Series an

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 9 CE Compliance If your data acquisition system needs

JP1 and JP2 in LogBook/360 Proper jumper configuration limits LogBook/360’s P1 bus to one power source. There should never be more than one power so

DBK48, pg. 10 967792 8B Isolated Signal Conditioning Module Using the DB25 Signal Output Connector Important Notes Regarding the Signal Output Conn

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 11 Jumper Assignments JMP1 JMP2 JMP3 JMP4 JMP5

DBK48, pg. 12 967792 8B Isolated Signal Conditioning Module Bringing Eight 8B Module Outputs to the DB25 Signal Output Connector With 3 jumper netw

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 13 Powering the System The DBK48 contains an internal

DBK48, pg. 14 967792 8B Isolated Signal Conditioning Module DaqView Configuration Main Window mX +b, an Example The Customize Engineering Units

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 15 Engineering Units Conversion Using mx + b Most of ou

DBK48, pg. 16 967792 8B Isolated Signal Conditioning Module Specifications – DBK48 Name/Function: DBK48, 16-slot Multi-Purpose Isolated Signal Condi

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 17 8B Module Ranges Voltage Input Modules (3 Hz BW) Par

DBK48, pg. 18 967792 8B Isolated Signal Conditioning Module Voltage Input Modules (1 kHz BW) Part No. Input Range Output Range SC-8B40-01 ±10 mV

8B Isolated Signal Conditioning Module 967792 DKB48, pg. 19 A NOTE FOR USERS OF CABLE CA-208 The following app