Measurement-computing WaveBook rev.5.3 Manual de usuario Pagina 140
- Pagina / 154
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9-4 Fuse Replacement
989396 WaveBook User’s Manual
9. While wearing a grounded wrist strap, remove and replace the bad F201 fuse. Ensure that the new
fuse is fully seated.
10. Position the Rear Panel onto the WaveBook/516E chassis.
11. Thread the two #4-40 hex Jackscrews back into the EXPANSION CONTROL connector.
Tighten snug.
12. Thread the six #4-40 hex Jackscrews back into the EXPANSION PORT connectors.
Tighten snug.
13. Thread the two Rear Panel Side Screws and the Bottom Panel Screw and tighten snug.
14. Place the BNC Washer at the base of the EXPANSION SIGNAL IN BNC connector.
15. Place the BNC Nut over the EXPANSION SIGNAL IN BNC connector and thread by hand.
Using the wrench and 9/16” deep-well socket, tighten the BNC Nut snug.
16. Return the WaveBook/516E to normal service. Should any problems be noted, consult the factory.
- WaveBook 1
- About WaveBook Documentation 5
- Table of Contents 7
- Chapter 3 – System Examples 7
- Step 1 - Install Software 9
- *324604B-01* 10
- Before you get started 11
- *324605B-01* 12
- What Are WaveBooks? 13
- WaveBook Product Comparison 14
- What Are WBKs? 15
- Minimum Requirements 21
- WaveBook/516E Front Panel 22
- WaveBook/516E Rear Panel 22
- WaveBook/516A 25
- Parallel Port Connections 26
- Ethernet Connections 28
- CAUTION 29
- Install the Software 29
- For DEDICATED Networks 39
- Adding WBK Option Cards 41
- Adding WBK Modules 43
- DIN 5 Power Pinout* 44
- The Daisy-Chain Concept 46
- Scan Synchronization 47
- System Power, Examples 51
- Power Supplies 52
- 14 VDC Mode (default) 53
- 28 VDC Mode 53
- Hardware Setup 53
- Charging 54
- Environmental Concerns 58
- Fuse Replacement 59
- Introduction 61
- Cable Review 62
- WaveBook Fan 71
- Basic Operation 72
- WaveBook/516E Block Diagram 73
- Digital I/O Connections 83
- 8-Bit Mode 84
- Triggers 85
- Multi-Channel Trigger 86
- Trigger Level 88
- Trigger Latency & Jitter 89
- Pulse Trigger 90
- Digital-Pattern Trigger 91
- Note: The Clock Divider 92
- PDF NOTE: 93
- SYNC Notes: 94
- Programmable Features 95
- Selecting a Channel’s Units 96
- (b) for the application in 97
- WaveView_WaveCal.pdf 99
- PostAcquisition Analysis.pdf 99
- ProgrammersManual.pdf 99
- WaveView Out-of-the-Box 100
- Software 100
- Calibration Software 104
- Overview 105
- CE Standards and Directives 105
- Safety Conditions 106
- Shielded 107
- BNC Connector 107
- Dust Cap 107
- Noise Considerations 108
- Product Care 109
- Driver Support 110
- Troubleshooting Tables 111
- Channel readings are wrong 115
- WaveView Scope stops 116
- Ethernet Problems 119
- Parallel Port Problems 122
- – continued 124
- (continued) 124
- Frequently Asked Questions 126
- (5) Topic: ECP and EPP 128
- (6) Topic: Sampling Rates 128
- (7) Topic: Calibration 129
- Customer Support 130
- Specifications 8 131
- (Note 2) 133
- General Information 137
- WaveBook/516E 139
- 9-4 Fuse Replacement 140
- WaveBook User’s Manual 140
- 897495 Appendix A 142
- Before you run a test 147
- 927096 Appendix B 148
- Glossary 151
- 969597 Data Acquisition 152
Relacionado con productos y manuales para Hardware Measurement-computing WaveBook rev.5.3
(108 paginas)Securitron AQU128B manuali
Manuali dei proprietari e guide per l'utente per Alimentatori elettrici Securitron AQU128B.
We fornisce 1 manuali pdf Securitron AQU128B per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Comentarios a estos manuales