Measurement-computing WaveBook rev.4.0 Manual de usuario Pagina 68
- Pagina / 82
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6-2 Troubleshooting
05-22-01
WaveBook User’s Manual
ReadMe Files and the Install CD-ROM
The Install CD-ROM includes ReadMe Files. These files often contain late-breaking information that may
not appear in the user documentation. During installation you should review the ReadMe files when
prompted to by the program.
The Install CD-ROM includes:
•
WaveBook Windows NT/2000 driver
•
WaveBook Windows 95/98/Me driver
•
DaqX.DLL
(32-bit API) for WaveBook
•
Microsoft C/C++ API support
•
Microsoft VB API support
•
Borland Delphi API support
•
Daq* Configuration Control Panel Applet
•
Program User’s Manual (PDF)
Upon installation, the user needs to run the Daq* Configuration Control Panel applet. The applet is used to
configure WaveBook for an appropriate LPT port. This must be performed in order for the application to
access WaveBook through the Windows NT/2000, or Windows 95/98/Me driver.
Driver Support
The daqX API can be used with WaveBook, DaqBook, DaqBoard, Daq PC Card and TempBook product
lines. All daqX functions share the
daq
prefix.
The API support examples can be found in the installed directory
\LANGS\WAVEBOOK
.
Connection Problems
Make sure the parallel port is operable and capable of generating interrupts. The parallel port, to which the
WaveBook is to be connected, must be properly configured in order for the device to operate correctly.
Each device must be configured using the Daq*Configuration Applet [located in the Windows’ Control
Panel]. If a device is not configured correctly it will not be accessible from an application.
If communications cannot be established with the WaveBook or, if trying to connect causes the system to
hang or crash, try the following:
•
Verify that the MODULE POWER switch is set to ON and that the MODULES ON indicator is lit.
•
Check to make sure that the Notebook PC communication cable is properly connected to the
WaveBook’s DB25 connector labeled “TO COMPUTER PARALLEL PORT.”
•
Check that the desired LPT port is properly configured and the base address and interrupt are
recognized by the operating system.
•
Check the BIOS settings for the LPT port. Make sure that the BIOS LPT protocol settings are
compatible with the settings selected for the LPT port. "Compatibility mode" is recommended.
•
Run the Daq Configuration applet from the Windows Control Panel. Make sure the device is
configured to the appropriate LPT port with the appropriate protocol. Run the device test and if it fails
try other protocols for the device. Be sure to click on
<Apply>
to apply the settings, before re-running
the test.
•
Windows NT/2000: Make sure that the driver has been loaded. The installation will configure the
operating system to automatically load the driver at boot-up. However, if there is a problem
communicating with the device, the driver can be loaded manually by using the following start
sequence from a DOS shell:
NET START WAVEBK
.
To unload the driver manually, use the following sequence:
NET STOP WAVEBK
.
•
Users of Enhanced Capabilities Ports (ECP) should refer to the ECP Setup section on page 6-3.
- WaveBook 1
- About This Manual 5
- Table of Contents 7
- WBK Document Modules 8
- Software Document Modules 8
- Unpacking 1-1 9
- 1-2 Unpacking 10
- WaveBook User’s Manual 10
- What are WaveBooks? 11
- WaveBook Product Comparison* 12
- What are WBKs? 13
- Used with WaveBook/516 Only 14
- WaveBook System Components 15
- 05-22-01 17
- Analog Specifications 19
- Triggering 20
- External Clock 20
- Introduction 23
- Connecting a WaveBook to a PC 23
- Adding WBK Option Cards 24
- Adding WBK Modules 26
- Dust Cap 27
- Shielded 27
- BNC Connector 27
- DIN 5 Power Pinout* 28
- 05-15-01 29
- Stacking Modules 30
- Connecting Encoders to WBK17 30
- &$87,21 31
- Three System Examples 33
- Power Supplies 35
- 14 VDC Mode (default) 36
- 28 VDC Mode 36
- Hardware Setup 36
- Charging 37
- Environmental Concerns 41
- Fuse Replacement 42
- Installing Software 43
- 06-08-01 47
- WaveBook/516, Basic Operation 50
- WaveBook/516 Fan 51
- Digital I/O Connections 53
- Triggers 55
- Multi-Channel Trigger 56
- Trigger Latency & Jitter 59
- Pulse Trigger 60
- Digital-Pattern Trigger 61
- Programmable Features 62
- Selecting a Channel’s Range 63
- Selecting a Channel’s Units 63
- Simplifying gives you: 64
- This means: 64
- Software, An Introduction 5 65
- Icon-Based Software 66
- Product Care 67
- Driver Support 68
- Connection Problems 68
- 32-Bit WaveView Issues 69
- Windows 95/98/Me Issues 69
- 6-4 Troubleshooting 70
- Troubleshooting 6-5 71
- 6-6 Troubleshooting 72
- Frequently Asked Questions 73
- (5) Topic: ECP and EPP 74
- (6) Topic: Sampling Rates 74
- Topic: Calibration 75
- (9) Topic: WaveView 76
- Customer Support 77
- 6-12 Troubleshooting 78
- Glossary 79
- Glossary 3 81
Relacionado con productos y manuales para Hardware Measurement-computing WaveBook rev.4.0
(140 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales