Measurement-computing eZ-PostView rev.2.0 Manual de usuario Pagina 97
- Pagina / 144
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
eZ-Analyst 969795 Edit Menu 4-19
Understanding Total Measured Data
In this figure, the Start Recording panel’s PreAcq-Trigger data and the Stop Recording Panel’s
Trigger Delay data are both saved as part of the total measured data.
Edit Menu > Configuration > Recording Setup Tab: Stop Recording Panel
Provide a means of setting the following parameters that pertain directly to stop recording:
Recording Duration sets a “time-out” which the recording event is not to exceed. If an
acquisition has been triggered, the measurement will run until either (a) the amplitude-based
Enable Stop Trigger Condition is met, or (b) the Recording Duration is met, whichever occurs
first. When the Recording Duration value is met, the recording event is aborted.
Note: Entering a value of “0” in the Recording Duration block sets the duration to infinity.
Enable Stop Trigger – if the checkbox is checked, amplitude-based data can be set as a
stop condition for the recording. The following options are provided.
Amplitude-Based
Data Types
Peak Time >=
Peak Time <
Spectrum >=
Spectrum <
at specified frequency
Delay (sec) – this function is used to include [with the recording] data that follows the stop
trigger event by the set number of seconds, as specified by the delay.
Maximum Duration Limit Terminating a Measurement
- Users of these Applications 1
- User’s Guide 2
- 06-17-02 5
- Playback Task Bar 7
- System Requirements 8
- Software Installation 9
- Getting Started 1-3 10
- 1-4 Getting Started 11
- Contents 12
- Features of eZ-PostView 12
- 09-05-02 13
- File Menu 14
- Edit Menu 15
- Configuration Window 15
- Acquisition Tab 16
- Channels Tab 17
- Playback Setup Window: 18
- Source Information Panel 18
- 2-8 Menus and Windows 19
- Menus and Windows 2-9 20
- 2-10 Menus and Windows 21
- Window Menu 22
- > Cascade 23
- > Tile Vertically 23
- > Tile Horizontally 24
- > Refresh Windows 24
- 2-14 Menus and Windows 25
- 08-30-022 26
- How to Change “Focus” 27
- Other Features 28
- Label / List 29
- Changing the Display Range 30
- 08-30-02 31
- Keyboard Controls A 32
- Keyboard Controls 33
- Appendix A 33
- Display Menu Control 35
- Plot Display Controls 35
- Plot Display Control 36
- Software Reference 37
- Manual Layout 39
- 978395 eZ-Analyst Series 40
- Table of Contents 41
- Software Installation 1 43
- 979495 eZ-Analyst 44
- ZonicBook/618E 45
- 979595 eZ-Analyst 46
- ZonicBook Medallion 47
- (All Windows Systems) 50
- 979595 Introduction 2-1 51
- 979595 eZ-Analyst Series 52
- 979595 Introduction 2-3 53
- A Look at eZ-Analyst 55
- Measurement Mode 57
- Change 58
- Task Mode 58
- Menus 3 59
- > Measurement Mode 60
- 3-3 61
- Starting FSV 62
- Channel Gauges 62
- An Example of Auto-Ranging 63
- Task Menu > Calibration 64
- 3-7 65
- 3-9 67
- Control Menu 68
- Export Menu 69
- > Function Data Set(s)* 70
- > Delete Window 72
- > Input Channels 72
- 979595 Menus 3-15 73
- Edit Menu 4 79
- Configuration . . 80
- 969795 Edit Menu 4-3 81
- Analyzer Tab 82
- (higher Delta X) 83
- Category Description 84
- 969795 Edit Menu 4-7 85
- 969795 Edit Menu 4-9 87
- 969795 Edit Menu 4-11 89
- Input Channels Tab 91
- Calibration 93
- Synopsis of Tach Modes 95
- Counter Mode 95
- Period Mode 95
- Voltage Mode 95
- 969795 Edit Menu 4-19 97
- 969795 Edit Menu 4-21 99
- 969795 eZ-Analyst 100
- 969795 Edit Menu 4-23 101
- Octave Setup Tab 102
- 969795 Edit Menu 4-25 103
- FFT Setup Tab 104
- 969795 Edit Menu 4-27 105
- 969795 Edit Menu 4-29 107
- 969795 Edit Menu 4-31 109
- WARNING 111
- 969795 Edit Menu 4-35 113
- 969795 Edit Menu 4-37 115
- Display Preferences 117
- Panel Function 117
- Introduction 119
- Adding and Removing Channels 119
- Using Cursors 120
- 969895 eZ-Analyst 122
- Using the Toolbar Buttons 124
- Additional Functionality 129
- Overlays of XLS Files 130
- (continued) 136
- Keys Function Comments 137
- 957595 Appendix A 138
- Glossary 139
- 957397 eZ-Analyst 140
- 957397 Glossary G-3 141
- 957397 Glossary G-5 143
Relacionado con productos y manuales para Hardware Measurement-computing eZ-PostView rev.2.0
(12 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.265 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales